0
alextseng

您好

我遇到的問題是當我將Ameba RTL8195設定為web server時,接上的sensor只有在每一次web server收到client的request時才會有更新。

我希望可以做到當Ameba設定為web server時,同時還可以每500 ms更新一次sensor數據。

目前使用的是arduino的原生範例wifi->simplewebserverwifi下去改,主要是因為我希望可以透過網頁做控制,所以選擇這個範例。

想請教我應該如何修改才可以達到這樣的效果,謝謝

 

完整的code如下:

/*
WiFi Web Server LED Blink

A simple web server that lets you blink an LED via the web.
This sketch will print the IP address of your WiFi Shield (once connected)
to the Serial monitor. From there, you can open that address in a web browser
to turn on and off the LED on pin 9.

If the IP address of your shield is yourAddress:
http://yourAddress/H turns the LED on
http://yourAddress/L turns it off

This example is written for a network using WPA encryption. For
WEP or WPA, change the Wifi.begin() call accordingly.

Circuit:
* WiFi shield attached
* LED attached to pin 9

created 25 Nov 2012
by Tom Igoe
*/
#include <SPI.h>
#include <WiFi.h>

//新增的部份
#define DownIRsensor 3 //下降的極限位置(紅外線感應pin腳) 1代表沒有阻隔,0被遮斷
#define UpIRsensor 8 //上升的極限位置(紅外線感應pin腳) 1代表沒有阻隔,0被遮斷
#define DayNightSensor A0 //光敏電阻信號讀取腳位
int DayNightSensorStatus; //0代表晚上,1代表白天
int DayNightSensorValue=0;
int DownIRsensorStatus;
int UpIRsensorStatus;

void sensors() {
DownIRsensorStatus=digitalRead(DownIRsensor);
UpIRsensorStatus=digitalRead(UpIRsensor);
DayNightSensorValue=analogRead(DayNightSensor);
if (DayNightSensorValue <=400)
{
DayNightSensorStatus=1;
}
else
{
DayNightSensorStatus=0;
}

Serial.print("DownIRsensor ");
Serial.println(DownIRsensorStatus);
Serial.println(digitalRead(DownIRsensor));
Serial.print("UpIRsensor ");
Serial.println(digitalRead(UpIRsensor));
Serial.print("DayNightSensorStatus ");
Serial.println(DayNightSensorStatus);
delay(1000);
}
char ssid[] = "yourssid"; // your network SSID (name)
char pass[] = "password"; // your network password
int keyIndex = 0; // your network key Index number (needed only for WEP)

int status = WL_IDLE_STATUS;
WiFiServer server(80);

void setup() {
Serial.begin(9600); // initialize serial communication
pinMode(9, OUTPUT); // set the LED pin mode

// check for the presence of the shield:
if (WiFi.status() == WL_NO_SHIELD) {
Serial.println("WiFi shield not present");
while (true); // don't continue
}

String fv = WiFi.firmwareVersion();
if (fv != "1.1.0") {
Serial.println("Please upgrade the firmware");
}

// attempt to connect to Wifi network:
while (status != WL_CONNECTED) {
Serial.print("Attempting to connect to Network named: ");
Serial.println(ssid); // print the network name (SSID);

// Connect to WPA/WPA2 network. Change this line if using open or WEP network:
status = WiFi.begin(ssid, pass);
// wait 10 seconds for connection:
delay(10000);
}
server.begin(); // start the web server on port 80
printWifiStatus(); // you're connected now, so print out the status
}
void loop() {
sensors();
WiFiClient client = server.available(); // listen for incoming clients
if (client) { // if you get a client,
Serial.println("new client"); // print a message out the serial port
String currentLine = ""; // make a String to hold incoming data from the client
while (client.connected()) { // loop while the client's connected
if (client.available()) { // if there's bytes to read from the client,
char c = client.read(); // read a byte, then
Serial.write(c); // print it out the serial monitor
if (c == '\n') { // if the byte is a newline character

// if the current line is blank, you got two newline characters in a row.
// that's the end of the client HTTP request, so send a response:
if (currentLine.length() == 0) {
// HTTP headers always start with a response code (e.g. HTTP/1.1 200 OK)
// and a content-type so the client knows what's coming, then a blank line:
client.println("HTTP/1.1 200 OK");
client.println("Content-type:text/html");
client.println();

// the content of the HTTP response follows the header:
client.print("Click <a href=\"/H\">here</a> turn the LED on pin 9 on<br>");
client.print("Click <a href=\"/L\">here</a> turn the LED on pin 9 off<br>");

// The HTTP response ends with another blank line:
client.println();
// break out of the while loop:
break;
} else { // if you got a newline, then clear currentLine:
currentLine = "";
}
} else if (c != '\r') { // if you got anything else but a carriage return character,
currentLine += c; // add it to the end of the currentLine
}

// Check to see if the client request was "GET /H" or "GET /L":
if (currentLine.endsWith("GET /H")) {
digitalWrite(9, HIGH); // GET /H turns the LED on
}
if (currentLine.endsWith("GET /L")) {
digitalWrite(9, LOW); // GET /L turns the LED off
}
}
}
// close the connection:
client.stop();
Serial.println("client disonnected");
}
}

void printWifiStatus() {
// print the SSID of the network you're attached to:
Serial.print("SSID: ");
Serial.println(WiFi.SSID());

// print your WiFi shield's IP address:
IPAddress ip = WiFi.localIP();
Serial.print("IP Address: ");
Serial.println(ip);

// print the received signal strength:
long rssi = WiFi.RSSI();
Serial.print("signal strength (RSSI):");
Serial.print(rssi);
Serial.println(" dBm");
// print where to go in a browser:
Serial.print("To see this page in action, open a browser to http://");
Serial.println(ip);

}

sean 回答了